Segmental bridge

src: www.cwbaecom.com

As its name implies, a segmental bridge is a bridge built in short sections (called segments), i.e., one piece at a time, as opposed to traditional methods that build a bridge in very large sections. The bridge is made of concrete that is either cast-in-place (constructed fully in its final location) or precast concrete (built at another location and then transported to their final location for placement in the full structure).

These bridges are very economical for long spans (over 100 meters), especially when access to the construction site is restricted. They are also chosen for their aesthetic appeal.

Video Segmental bridge

History

The first segmental concrete bridge, built in 1950, was cast-in-place across the Lahn River in Balduinstein, Germany.

The first precast segmental concrete bridge, built in 1962, crossed the Seine River in France.

Maps Segmental bridge

Construction

The sequence of construction is similar to traditional concrete bridge building, i.e., build the support towers (columns), build the temporary falsework, build the deck, perform finish work. The principal differences are as follows:

1. The support towers may be built segmentally. Often this is accomplished using "slip-form" construction, where the falsework moves (slips) upward following sequential concrete "pours." The falsework uses the newly constructed concrete as the basis for moving upward.
2. After the towers are built, a superstructure is built atop the towers. This superstructure serves as the "launching" point for building the deck. (The deck is often built in both directions away from the tower, simultaneously.)
3. The deck is now constructed sequentially, beginning at the tower, one section at a time. This process is usually accomplished using a self propelled bridge layer that hoists the bridge section into place.
   • In cast-in-place bridges, the falsework is connected to the previously installed concrete and allowed to cantilever freely. Next, the permanent reinforcing steel and supports are installed. Finally, the concrete is placed and cured, freeing the falsework to be moved.
   • In pre-cast bridges, the concrete segment is constructed on the ground, and then transported and hoisted into place. As the new segment is suspended in place by the crane, workers install steel reinforcing that attaches the new segment to preceding segments. Each segment of the bridge designed to accept connections from both preceding and succeeding segments.
4. The process in step 3 is repeated until the span is completed.

src: c8.alamy.com

Notable examples

• Chesapeake and Delaware Canal Bridge in Delaware is a cable-stayed bridge using precast concrete segments for the approach and center spans
• Vancouver SkyTrain's Millennium Line as well as the elevated portion of the Canada Line.
• Linn Cove Viaduct in the Blue Ridge Mountains, North Carolina (precast)
• Manwel Dimech Bridge in St. Julian's (San ?iljan), Malta. This bridge connects the two parts of Regional Road and pass over G?omar Valley.
• Seven Mile Bridge in the Florida Keys (precast)
• The Interstate H-3 viaducts through the Ko'olau Mountains, Oahu, Hawaii (CIP Segmental)
• The new Pennsylvania Turnpike (I-76) bridges over the Susquehanna River south of Harrisburg, Pennsylvania (precast)
• The Eastern span replacement of the San Francisco-Oakland Bay Bridge viaduct (precast)
• The Benicia-Martinez Bridge (northbound span) between Benicia and Martinez, CA (CIP Segmental)
• The Four Bears Bridge over the Missouri River in North Dakota utilizes precast concrete segments, erected with the balanced cantilever method (precast)
• The High Five Interchange connecting US-75 and I-635 in Dallas, TX (precast)
• The AirTrain linking NY's John F. Kennedy International Airport with the Jamaica Transit Center
• The ramps leading between the Brooklyn Queens Expressway (NY I-278) and the Williamsburg Bridge (connecting to Manhattan)
• The elevated sections of the Delhi Metro
• The elevated sections of the Dubai Metro
• The I-35W Saint Anthony Falls Bridge in Minneapolis, MN, is notable primarily for the bridge it replaced: I-35W Mississippi River bridge which collapsed on August 1, 2007.
• The Veterans' Glass City Skyway in Toledo, OH
• Canada's Confederation Bridge linking the provinces of Prince Edward Island and New Brunswick
• Bridge over River Kosi between Saharsa and Darbhanga in Bihar, India.
• Zilwaukee Bridge crossing the Saginaw River on I-75 north of Saginaw in Zilwaukee, Michigan
• The Pitkins Curve bridge on California State Route 1 near Big Sur is a CIP segmental bridge bypassing a rock-slide portion of a scenic motorway.
• Portions of the Interstate 4 - Selmon Expressway Connector in Tampa, Florida

src: customer.djc.com

References

src: finleyengineeringgroup.com

Further reading

1. LoBuono, J. (2005). "Assembly required-The instructions for building New Jersey's first segmental bridge." Chicago, Illinois: GoBridges.com. September/October. Published October 18, 2005 at http://www.gobridges.com/article.asp?id=770
2. (2006) "Design & Construction of Ngong Shuen Chau Viaduct" International Conference on Bridge Engineering - Challenges in the 21st Century, Hong Kong, 1 ~ 3 November 2006 http://www.ywlgroup.com/Articles.html
3. (2007) "Construction of the Precast Segmental Approach - Structures for Sutong Bridge" ICE Conference 2007, Beijing http://www.ywlgroup.com/Articles.html

src: www.wikabeton.co.id

Related sites

• http://www.fhwa.dot.gov/bridge/segmental/index.htm
• http://www.asbi-assoc.org/
• http://www.figgbridge.com/
• http://www.finleyengineeringgroup.com/index.cfm/home
• http://www.mcnarybergeron.com/
• http://www.pbworld.com/news_events/publications/network/issue_57/57_03_murilloj_briefhistoryseg.asp
• http://www.pbworld.com/news_events/publications/network/issue_28/28_16_wahlp_constructionsequence.asp
• http://www.polito.it/creepanalysis

Source of article : Wikipedia